홈페이지> 블로그> Guide Rail Elevator Maintenance Rail Elevator Maintenance

Guide Rail Elevator Maintenance Rail Elevator Maintenance

July 27, 2021

For rail lift maintenance, it is closely related to maintenance. Without good maintenance, there will be many problems with maintenance. There are some common maintenance problems that are actually caused by poor maintenance. The solution is the maintenance process. Here are some common rail lift maintenance related knowledge.

Rail lift maintenance

It was found that the DIN rail lifts are unstable. This condition is generally caused by the fault of the motor. The solution is to clean the control boxes and related distribution boxes. Keep the equipment clean by cleaning. In addition, it should also be noted that it is to check whether the operation of each institution can be operated normally, and whether noise is present. These need to be promptly discovered and eliminated in a timely manner.

In the maintenance of guide rail lifts, it is often found that it has a phenomenon of electric leakage. This requires us to check the places where the wires of related equipment are not damaged, and to replace and wrap them in time. In addition to other parts of the brush, the corresponding contact surface must be cleaned accordingly, and the corresponding brush pressure is adjusted.

Friction sounds occur in the maintenance of DIN rail lifts. This is usually the case of gears. When repairing, check the gear box, gear box and external gears. These parts are most likely to have friction and should be lubricated in time.

The phenomenon of motor overheating in the maintenance of DIN rail lifts will also occur frequently. When this happens, we need to stop in time to check the associated lubrication and internal faults of the motor.

The problem of wire rope is also common, this is generally caused by the use of too long. Guide rail lift maintenance is also a good solution to the problem of wire rope, as long as the regular inspection and replacement on it. It is necessary to ensure the safe operation of the entire lift.

Guide rail lifts maintenance

Guide rail type hydraulic lift should pay attention to maintenance when using it in daily life to prolong its life. Understand the maintenance and maintenance issues of mechanical equipment:

1. The brakes of various agencies should always check and adjust the clearance between brake shoes and brake wheels to ensure flexibility and reliability. On the friction surface, there should be no dirt, dirt must be washed off with gasoline or thinner.

2. Lubrication and hydraulic oil of various parts such as gearboxes, gearboxes, and external gears are performed according to the requirements in the lubrication table.

3. Attention should be paid to checking whether there are broken wires and loose strands in the wire ropes of various departments. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of wire ropes should strictly comply with the provisions of GB5144-85.

4. Check the connection of each department frequently and tighten it if loose. The body connection bolts should be checked for tightness when the body is stressed (rotating arms can be used to create compression). All connecting shafts must have cotter pins and must be fully opened.

5. Regularly check whether the operation of each institution is normal and whether there is noise. If any malfunction is found, it must be promptly removed.

6. When installing, disassembling and adjusting the rotary mechanism, it is necessary to ensure that the centerline of the reducer of the rotary mechanism is parallel to the centerline of the gear, and the mating surface is not less than 70%, and the meshing clearance should be suitable.

7. Always check all wires and cables for damage. Should be timely dressing and replacement of the damaged part.

8. If the motor is overheated, stop it in time and continue to run after troubleshooting. The lubrication of the motor bearing should be good.

9. Each part of the brush, the contact surface should be kept clean, adjust the brush pressure, so that the contact area is not less than 50%.

10. Each control box, distribution box, etc. are often kept clean, and dust on electrical equipment is cleaned in time.

문의하기

Author:

Ms. Angela

Phone/WhatsApp:

+8618115668569

인기 상품
You may also like
Related Categories

이 업체에게 이메일로 보내기

제목:
이메일:
메시지:

Your message must be betwwen 20-8000 characters

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

송신